Card spend controls
A card’s controls say where it works, how much it may spend and how often, and which merchants and countries it may pay. Open the card and choose the pencil beside Limits and rules to change them. Controls only narrow: a limit never lets through what the account’s available balance would refuse.
Limits
A limit has a scope, a period, and an amount, a count, or both.
| Part | Choices |
|---|---|
| Scope | All spend, one channel (ATM, in store or online), or one merchant category group |
| Period | One transaction, the day, the month, or the card’s life |
| Amount | The most the card may spend in the period, in the card’s billing currency |
| Count | The most purchases the card may make in the period |
A day is your organisation’s trading date, and a month is its calendar month. The card’s life starts when it is issued and carries on through a reissue. A transaction limit has no count.
Within one scope, a longer period never allows less: a day never allows more than its month. A limit on one scope may sit above another scope’s: a cash limit above the all-spend day is accepted, and the lower one binds when a purchase meets both.
A single-use card is a limit of all spend, for the card’s life, with a count of 1.
What counts as spent
A limit counts every purchase approved in its period, less anything the merchant reversed. A purchase still counts after it clears or its hold expires, so a single-use card stays used. A declined purchase counts for nothing.
The card’s Limits and rules section shows each limit with what this period has used.
| Limit | Used on 2 November 2026 |
|---|---|
| 2,000.00 a transaction | — |
| 5,000.00 a day | 2,300.00 over 2 purchases |
| 20,000.00 a month | 2,300.00 over 2 purchases |
Category and country rules
A card may carry one category rule and one country rule. Each either blocks a list or allows only a list.
- A category rule names merchant category groups.
- A country rule names ISO 3166 countries.
Both rules apply to every purchase, online included. A merchant category in no group passes a block rule and fails an allow-only rule. So does a purchase whose merchant country is not given. An allow-only list names at least one entry: a card that may be used nowhere is a suspended card.
An allow-only country rule replaces the in-store-abroad check. A block rule leaves that check in place.
The card type’s bounds
Your organisation sets the most a card of each type may be allowed. Every limit on a card sits within its type’s bounds, and a group the type always blocks is blocked whatever the card says.
- A limit you add or raise above a bound is refused.
- If the bound is lowered later, a card above it keeps its limit. The lower bound applies to purchases from that day, and the card shows the product’s bound beside its own limit.
- An allow-only category rule cannot name a group the type always blocks.
Valid until
A card may carry a last day of use. From the next trading date, every purchase is declined as card lapsed. Purchases approved before then clear as usual.
At end of day, a lapsed card with no open hold is closed. While a hold is open, the card waits for the end of day whose clearing or expiry frees it. Move the date later, or clear it, to bring a lapsed card back before it closes. The date is never before today.
Why a purchase was declined
The card’s Authorisations tab lists each purchase, newest first, 50 at a time. Select Load older for earlier purchases. A declined purchase names its reason and the rule that declined it, so you can tell who can change it.
| Purchase | Answer | Declining rule |
|---|---|---|
| 1,500.00 at a grocer in ZA | Approved | — |
| 2,500.00 at a grocer in ZA | Ceiling exceeded | transaction, all spend, 2 000.00 |
| 100.00 at an online casino | Merchant category not allowed | category gambling, blocked by the card type |
| 800.00 online from GB | Approved | — |
| 300.00 online from US | Country not allowed | country US, not in the allow list |
The checks run in a fixed order, and the first that fails is named:
flowchart LR
A[Card active] --> B[Valid until]
B --> C[Channel switch]
C --> D[Card type blocks]
D --> E[Category rule]
E --> F[In store abroad]
F --> G[Country rule]
G --> H[Limits]
H --> I[Funding]
Limits run shortest period first, then all spend, a channel, and a category group. Within one limit, the amount is checked before the count.
The processor receives only a response code, following ISO 8583 — see the standards register row ISO 8583 — card transaction messages: 61 for an amount, 65 for a count, 57 for a blocked category, country or channel, and 54 for a lapsed card.
What your organisation configures
- The merchant category groups, and their ranges — see Merchant category groups.
- Each card type’s bounds, and the groups it always blocks — see Card types.
- Each card’s limits, rules and valid-until date, set by a clerk, or by a corporate’s administrator — see Corporate cards.
From the LedgerTM product guide, as shipped with the software and written with it. Copied from the platform repository on 2026-11-11.